Gas hob under the countertop. How to install a built-in hob into a countertop? Installation and sealing

The layout of modern kitchen furniture sets includes a built-in electric or gas stove, the hob and oven of which are mounted separately. The built-in panel is a functionally complete product that, in principle, can be used without a kitchen. This article will explain how the installation of an embedded hob and connecting to the network with your own hands. The surface can be electric, gas or a combination, but the basic rules that should be followed when working are the same for all versions.

Step-by-step installation instructions

Speaking of tools, if the built-in panel is installed in a new set, and the hole for mounting the housing in the countertop has not yet been made, you will need a drill and electric jigsaw. To connect to the electrical network, you will also need a screwdriver, pliers, and a voltage indicator.

The first thing you should take care of is a 220-volt electrical outlet into which the built-in hob will be connected. The choice of its location and installation must be done before installing the furniture. Included kitchen stove In addition to the panel, there is an oven. If the first one is installed without a cabinet, it can be plugged into one outlet. The electrical outlet should be installed lower than the built-in hob will be located to prevent it from being exposed to moisture and grease during cooking.

In the era of new technologies, inconvenient and bulky gas and electric stoves are being replaced by completely the new kind kitchen equipment. These are hobs. Such devices fit harmoniously into the design kitchen furniture, convenient to use. Installing a hob into a countertop with your own hands is a fairly simple process. Even if you have a little skill in working with power tools, even a beginner can handle this task. At the same time, you can save money on installation services.

Hob selection

These kitchen appliances have virtually no drawbacks. All devices can be divided into categories:

• electrical;
• gas;
• combined;
• induction

According to the material of manufacture:

• stainless;
• ceramic;
• glass;
• enameled.

In this case, the panel may have different number burners and their varied arrangement on the surface. At the first stage, you need to choose the most convenient and suitable device. When ordering kitchen furniture, you need to think in advance about the installation location in the furniture. It is possible that an oven will be installed along with the panel. You need to think about it first about connecting to the network: to gas pipe when choosing a gas panel and to the electrical network if you prefer an electrical device.

To install the electrical network, it is imperative to provide the cross-section of the power cable and the power of the socket, taking into account the current consumption of the panel and the possible oven specified in the instructions. Do not forget about grounding or protective grounding metal parts electrical appliance. After preparation, you can start working.

Installing a hob into a countertop with your own hands is a simple process, accessible even to a beginner . First you need to prepare All necessary materials and tools. The insertion of the hob into the countertop begins with drawing dimensions. Further installation depends on how correctly and accurately the markings are made. First you need to remove from the panel all parts that may fall out during installation (these are protective grilles, burners, controls).

Applying markings to the tabletop

The dimensions for the technological hole in the countertop can be specified by the manufacturer in the instructions. If they are not there, you will have to take the measurements yourself. It is not difficult. To do this, you need to turn the panel over and take its dimensions, taking into account that it should lie on the tabletop along the entire perimeter. For convenience, you can make a template by cutting it out of a sheet of cardboard according to the appropriate sizes. Then transfer the dimensions to the tabletop using a long ruler, square or prepared template. With maximum precision to avoid curvature, use a pencil or marker to draw the outline on the tabletop.

Window cutout for panel installation

After making sure that the markings are correct, you can begin cutting out the hole. Using a drill with a diameter larger than the width of the file of the jigsaw used by 2 mm, drill 4 holes along internal corners drawn outline. Insert the jigsaw blade into one of the holes and make a cut in the tabletop along the entire contour. To prevent large chips, you need to use a fine-toothed file or a hand router.

Place the panel to be installed into the resulting niche and align it. See from the outside whether everything is done smoothly. If everything is done correctly, proceed to the next one stage of cutting into the tabletop. Now treat the cut areas with sandpaper, a file, or a rasp. If the countertop used is made of wood, be sure to exclude the possibility of moisture penetration. To do this, carefully treat the cut area with moisture-proof material:

• silicone;
• sealant;
• nitro lacquer

If the tabletop is made of plastic materials, you can skip this processing. The plastic will not swell or swell due to moisture. Can be coated in several layers for reliability. After the last layer has dried, cover the cut with self-adhesive sealant. Preparations are complete. Installation can be done.

Installation and connection

Installing the hob into a prepared window is not difficult. To do this, lower the panel into the hole. Using measuring tool align its position. After making sure that it is correct, secure it from below with special brackets and screws to the table top. The brackets and screws are supplied by the manufacturer as a set. It would be useful to use a seal around the perimeter of the installed device. This step will also prevent debris and moisture from getting under the installed surface. Usually, it comes with the product.

All that remains is to reinstall all the previously removed parts and begin connecting the energy carrier. If the panel is gas, it must be cut into the gas line. If an electric one was installed, then connect it correctly to a pre-prepared electrical network. All that remains is to try it out and use it comfortably. You can watch the video to see how to install the hob correctly.

Complex stoves for the kitchen, which simultaneously combine a hob and an oven, are increasingly becoming a thing of the past. Modern housewives are using them less and less for their intended purpose. ovens. They are increasingly turning into storage for pots and pans.

Why overpay for an unnecessary metal cabinet, when you can buy a comfortable and aesthetic hob, and the free space created underneath is perfect for storing dishes and other things. Even an inexperienced craftsman can install a hob into a countertop, because its installation does not require any experience or qualifications.

Types of hobs

So, before you begin such a procedure as installing a hob into a countertop with your own hands (you can see the photo in this article), you should understand the types of these devices. There are the following main types of hobs:

1. Electrical.
2. Induction.
3. Gas.

It is advisable to entrust the installation and installation of the latter option to a professional, since incorrect connection can lead to serious problems. When using gas stoves indoors, special requirements must be observed. During installation electrical panels It is also important to observe caution and safety rules when working with high voltage. It is necessary to provide high-quality electrical power with grounding.

When purchasing a hob, it is important to pay special attention to it since the installation of the hob into the countertop should be done with a small margin around the edges. In addition, you need to decide on the insertion location. Conduct in advance

Tabletop installation

If you purchased a glass or stone countertop, it is advisable to have it installed by professionals. Since you do not know about all the intricacies of the process, you can damage an expensive item. If you can handle the installation yourself, but with some construction skills.

You will need the following:

• Grouting compound for tiles.
• Tiles for cladding the surface of the countertop.
• Assembly or tile adhesive.
• Tungsten coated tiles.
• Gun with silicone sealant.
• Electric jigsaw.
• Waterproof wood board.
• Set of tools - square, screwdriver, screws.

Replacing a countertop should begin with dismantling the old one. Despite the fact that you will not need the old countertop in the future, you must remove it very carefully to avoid damage to the kitchen set.

It is very important to adjust the new countertop to the dimensions of your furniture. It is likely that you will need to cut off the excess. In this case, the unprotected edges of the chipboard are exposed. This material absorbs moisture well, so the cuts need to be well treated with sealant. If the table top is mounted with saw cuts to the stove, it is advisable to close them using special end strips.

Required Tools

Before moving on to a process such as installing a hob into a countertop (the photos show what they are like), you need to prepare the following tools:

• Pencil.
• Roulette.
• Jigsaw.
• Drill-driver with a wood drill bit with a diameter of 8-10 mm.
• Sealant.

Preparatory process

First, you should make sure that in the place where the hob will be installed in the countertop, there are accessible ones. The presence of an outlet, a suitable length of the gas supply hose, without squeezing and kinks for a gas stove - these are two fundamental aspects.

If the wiring is old and you are not sure that it is reliable, it is recommended to run an independent cable for the stove directly from the meter.

Installing a hob into a countertop

1. First you need to make a hole in the tabletop. To do this, according to the instructions, an opening is marked. If there are no instructions, then
   The full dimensions are outlined, while on each side you need to retreat approximately 5 mm.
2. Using a drill, a hole is drilled so as not to go beyond the boundary of the contour. Then we continue working with a jigsaw. To reduce chipping, it is recommended to use a file with fine teeth. In addition, you can paste over the outline with stationery or masking tape.
3. After the cut is made, you need to paint or seal the cut edges to prevent the tabletop from swelling.
4. Next, the hob is installed in a 28 mm countertop, secured and connected to the network.

The insertion of the panel must be carried out with maximum precision. Otherwise, even a 1 cm error can ruin the countertop, which is one of the most expensive elements of a kitchen set.

Artificial stone countertop

Compared to its chipboard counterparts, the tabletop is made of artificial stone is the most durable. Despite this, the main problem is installing the hob into an artificial stone countertop.

In most cases, an artificial stone countertop is ordered with ready-made holes for a specific hob. But what if the countertop is already installed, but the hob is not yet? IN in this case the most reliable and the best option will give the countertop to qualified specialists who, with the help professional tool make the necessary hole.

If you still decide to take a risk, then this work can be produced using the technology described above, but only instead of a jigsaw you will need to take an angle saw grinder and a diamond-coated blade designed for cutting concrete.

It's important to remember that self installation the hob into the countertop must be carefully thought out at all stages of installation. Only in this case will less time be spent on this type of work, and their quality and subsequent result will also significantly improve.

This step-by-step instruction on how to cut a hole in a countertop made of chipboard or MDF for a hob with your own hands. When you probably need to know how to cut holes in chipboard or MDF countertops if you are installing a sink or cooktop. This task may seem simple, but we can assure you that there are many nuances that need to be taken into account for a good result.

On the one hand, you must carefully follow the outline of the gas stove using a template or follow the instructions indicated on the product. In most cases, there are certain restrictions that you must pay attention to, such as the minimum distance from the stove to the back panel or on both sides, to. Use a large L-shaped square to draw a rectangle on your workbench, otherwise the corners will not be at right angles.

To obtain precise hole, you must use a good saw with an appropriate blade. Therefore, the blade must have teeth oriented downward, otherwise it will split the surface. Drill starting holes along the four corners of the rectangle using a drill or (the hole should be wider than the size of the jigsaw blade).

Work plan for installing the hob into the countertop

Materials:

• table top;
• carpenter's pencil;
• insulating tape.

Tools:

1. Protective gloves, safety glasses;
2. Saw or jigsaw;
3. Tape measure, level, square;
4. C-clamps.

• Wear safety glasses when making cuts.
• Choose a blade with fine teeth.

Deadline

• 10 minutes

When installing a gas stove hob or hob, you must cut holes in the countertop.

Tip: Follow the manufacturer's instructions when cutting a hole in your kitchen countertop if you want to prevent potential problems.

How to cut a hole in a countertop for a hob

Guide line markings

The first step is to determine the outline of the slab. In most cases, it should contain instructions on how to do this, but there is a technique that only provides recommended hole sizes. Place the hob on top of the cabinets. Leave the recommended distance from the back panel to the front edge of the tabletop.

Draw a median on the countertop and mark the cut lines using the manufacturer's instructions.

Marking the countertop for the hole for the stove

As you can see in the picture, you need an L-square, a tape measure, and a carpenter's pencil to get the job done professionally. Make sure the cut lines are parallel and at right angles. In addition, the rectangle must be symmetrical.

Tip: Check that the rectangle under the kitchen cabinet, in which the hood will be built, and there is sufficient space around it (in accordance with the manufacturer's instructions).

Installing spacers under the countertop

To get an accurate result, you should place several spacers under the tabletop. However, the tabletop must be level.

You should leave about 2 inches of space between the cabinets and the countertop, otherwise the saw blade could damage them.

Making initial holes for drilling

Use a drill with a special bit to create starting holes along the corners. It is very important to line up the bits correctly, otherwise you may drill out of line.

Tip: Make sure you use good equipment for drilling with speed control. Set the drill at low speeds and hold the drill with both hands if you want to have good control over it. Repeat the process for each corner of the rectangle.

Passing the laminated layer

In this image you should notice that the drill bit is going through the top layer. Don't use too much high pressure on the drilling equipment, otherwise it may slip out of place.

We remove residues from the process with a vacuum cleaner

Drilling a hole in a countertop with a drill will create a lot of residue, so we recommend that you have someone clean it up as you make the hole.

Tip: Work with great care and attention, as it is important to make the holes exactly in the indicated places.

Initial holes for cutting in the tabletop

After drilling the corner pilot holes, you need to make cuts along the guide lines. If you are not experienced in this area, you should cover the cut lines with masking tape. This way you will help prevent the edges from fraying.

Cutting a hole with a jigsaw in a tabletop

To make the cuts, we recommend that you use a jigsaw. Choose a blade with downward-facing teeth. In addition, the blade must have set teeth. If you have not worked with a jigsaw before, we recommend that you secure the tabletop. Make sure the blade follows the cut lines exactly.

Tip: Remove chips that form frequently, otherwise they may cover the lines. Set the jigsaw at low speeds.

Finished hole in the countertop for the stove

Last but not least, you need to take care of installing the hob into the countertop yourself. If you followed our tips and read the manufacturer's instructions, the hob should fit into the hole easily. However, if the edges are not completely straight, you can smooth them with silicone or caulk.

Tip: Use sandpaper to smooth the cutting edges.

Installing the hob into the countertop

After this, all you have to do is install the hob into the countertop, connect it and secure it with the screws that should come with it.

Thank you for reading our step by step recommendation How to cut a hole in a countertop and install a hob with your own hands, we recommend that you read other articles. Don't forget to share our projects with your friends using social network widgets.

The hob allows you not only to prepare any dish, but also to save space. After all, such equipment has smaller dimensions than large and bulky ones. gas stoves. How to install a hob and oven? It's simple. The main thing is to act according to the instructions. Everyone is capable of coping with such tasks. This does not require expensive equipment, but only the availability of certain tools.

What you need

In conclusion

Now you know how to build a hob into a countertop with your own hands. Before starting work, you should evaluate your skills and abilities. If you cannot do this, then you should seek help from professionals. However, it is safe to say that the installation process is not very difficult. Almost anyone can cope with such a task. The main thing is to carefully study the instructions and have everything at hand necessary tools. By doing similar works It is recommended to take into account all the nuances and subtleties of the process.