home Payment

Sawing laminate with a grinder. How to saw a laminate: we select a tool. Professional tools: cutter

If there is material, then there is a way to adjust it to the desired parameters. Laminate is no exception. In fact, you can cut the laminate yourself, but without knowing some of the nuances, you can render the material unusable.

For proper styling laminate, you will have to resort to sawing it, having previously learned how to saw the laminate.

As a rule, sawing along is used when laying the extreme elements so that the gap between the laminate and the wall is 10 mm. This requirement helps to subsequently avoid unpleasant creaking of the floor covering.

With the growing popularity of the laminate, the list of tools for cutting it increases, and the buyer chooses which file is better to cut.

Consider the most popular methods.

Sawing with an electric jigsaw is rightfully considered the most popular and high-quality way. Nuances:

We select a special file with fine teeth for sawing wood.
It is necessary to smoothly move the jigsaw over the material at high speeds.
The bar must be laid on a hard surface face down, if the teeth of the file are located with the teeth down, then the face up.

Bulgarian

Bulgarian - that's the better to cut the laminate. Nuances:

To avoid cracks when sawing, you should opt for discs for metal, and not for wood, or you should buy a special disc for sawing laminate.
Laminate plank is placed on a solid surface with a pattern down. The cut itself should be done slowly and smoothly so that the disc does not get stuck in the bar.
When the grinder and the laminate come into contact, a specific smell appears.

If there was neither a grinder nor an electric jigsaw at hand, you can take up a hacksaw. However, it is more suitable for sawing off small pieces, but sawing along the plank with a hacksaw is a rather long and laborious process. Nuances:

It is worth excluding cutting the laminate with a hacksaw with large teeth, as this will lead to damage to the material, to chips and scratches.
Preference should be given to a hacksaw for metal. It has a narrower canvas.
the material can first be rubbed with paraffin, which will somewhat strengthen the base and prevent the formation of chips.
The cut must be made on a solid surface.
The front side of the material should be on the bottom.
Avoid additional pressure when sawing.

Note! Working with a hacksaw with a thin blade is more laborious, but it is not the time spent on the work that matters, but the result.

Special tool

Laminate can not only be sawn, but also cut. To do this, there is a specially designed tool-machine for cutting laminate. Outwardly, it is very similar to a paper cutting tool. The machine for cutting laminate is a support with a blade, work with which begins by pressing the handle of this mechanism. This tool helps to make an even cut, while it does not make noise and prevents the formation of dust, sawdust and, most importantly, chips.

However, it is worth noting that its purchase will cost 2000 rubles, and this is not entirely advisable for a one-time use. If you are laying laminate professionally, and this is your profession, then, of course, this machine is the first thing you should buy.

Another important nuance machine - they can only make cuts across, but for longitudinal cuts it is still better to use a grinder or electric jigsaw.

The choice of tool for cutting laminate should be taken seriously, as this material is a pressed structure coated with an acrylic resin film, and improper handling will lead to deformation of the panel and the formation of chips.

Before cutting, measure a thousand and one times. The saw mark is placed on the back of the plank with a simple pencil. If a mark is needed on the front, it is recommended that you first stick a masking tape.

It is also worth considering what the width of the cut will be, it may vary depending on the tool used.

Note! Do not despair if the incision itself turned out to be not quite even. This is not yet a reason to throw away the bar; irregularities can be covered with a plinth. If scratches form during the cutting process, they can be masked with a special paste for laminate.

Any woodwork involves the appearance of wood dust, sawdust and debris. It is not recommended to engage in sawing the laminate in the room where it will be directly laid. For these works it is worth allocating another room.

Before laying the laminate, you need to carefully prepare the surface to avoid possible entry of various grains of sand into the locks of the laminate and under the material. The laminate itself should be wiped with a damp cloth. This procedure will subsequently help to avoid creaking of the laminate and increase its service life.

Video

This video shows a laminate cutter in action.

Laminate is the most common floor covering today, which is made from a compressed material - fiberboard (MDF). Appearance laminated board defines a decorative layer, usually imitating the surface of the tree, although other options are possible. The board itself consists of 4 layers, sealed ("laminated") in a protective film, due to which the material got its name.

The material is quite simple to install, so both professionals and ordinary home craftsmen who try to do everything with their own hands can do its installation. The technology is such that the laminate must be sawn at the time of laying. Accordingly, the question arises: How to saw the laminate so that the cut is neat and without chips?

About laminate

From practice it can be seen that it is almost impossible to fit laminate slabs to the size of the room, they need to be filed to the desired size. It is necessary to determine which file to cut the laminate so that the cut is even.

To do this, it is important to study the structure of the processed material.

The first, lowest layer of the product consists of unrefined paper. It protects against moisture penetration. Sometimes an additional substrate is added under this layer, which is designed for sound and heat insulation, but this makes the price of the product higher.
The next layer is made of HDF and the greater its density, the better the fixation between the panels.
Then comes a layer of decorative paper, on which imitation of various types of wood, stone, sand, marble and other natural materials can be depicted.
The topmost layer is colorless and consists of acrylic resin.. Through it, a decorative pattern on the panel is clearly visible. It is its thickness that affects the wear resistance class of the laminate and its service life.

Laminate flooring can be classified into residential and commercial. The latter has an increased resistance of the protective coating and is designed for rooms with increased "human traffic".

Sawing tool

When processing any structure, it is imperative to use tools that are suitable for this particular material composition. After all, it is impossible to cut ceramic with a jigsaw floor tiles, and glass cutter - metal products. So the best cutter for one raw material cannot be useful for another.

Any professional or just an "amateur" probably knows that to cut a laminate board, you need a special tool so that the structure of the material is not broken.

These tools include:

jigsaw;
a circular saw;
hacksaw;
laminate cutter.

Electric jigsaw

What is the best way to cut laminate? The best cut is obtained when using a jigsaw. A jigsaw file for laminate should be designed for working with wood.

Advice!
Before making a cut, on the laminated side of the board, it is necessary to draw the border of the cut with a pencil, then cut the protective film with a paint knife.

The board should be placed face down on a flat surface and fixed. At the time of cutting, it is very important not to make sudden movements, in order to avoid the formation of chips and damage to the structure of the material. A neat incision can be made both in the transverse and in the longitudinal direction.

Saw

In order to get a neat cut of a laminate board, you can use a hand-held circular saw with a disc for metal, called a grinder. As in the previous case, the board must be laid on a flat surface with the front side, firmly strengthening it. Gently lower the “grinder” disk and draw along the line marked with a pencil.

If neither one nor the other tool is available, you can use a hand saw or a hacksaw for metal. Using this method work with the utmost care. And the whole process takes a lot of time. This method is not easy and the cut is not of sufficient quality.

It can justify itself only with small amounts of work.

Cutter

For cutting laminate in large volumes, you can use a special cutter that looks like a sharp blade that descends on the material with a handle. Using this method, the laminate can only be cut in the transverse direction. The cut line is very precise. This method is convenient for those who are engaged in laying laminate on an ongoing basis, since the price of the tool is very “decent”.

What blade to cut laminate?

If the tool has already been selected, then you need to decide on its components. Jigsaw blades for laminate differ in shape, pitch and method of setting the teeth, as well as in the material of the blade. The quality of laying depends on the quality of cutting material elements. If you try to cut a laminate with a saw that is not intended for this, it is more likely to leave multiple chips on the edge of the workpiece.

If there is no special file for a jigsaw on a laminate, any file with fine teeth and a narrow blade can be used. For curly or curvilinear cuts, the narrower the canvas, the more accurate the cut will be.

A wood file should be with the direction of the tops of the teeth in the opposite direction. Due to this, the probability of chipping is excluded when sawing the material from the front side and excludes the “turning” of the decorative layer outward. The evenness of the cut is affected not only by the size of the teeth, but also by the speed with which the panel web is cut, as well as the quality of the metal from which the laminate saw is made.

If the farm has a circular saw, it can also be adapted for cutting laminate.

Instructions for cutting laminate using a circular saw looks like this:

It is important that the saw blades on the laminate have fine teeth;
A mark is applied to the front side of the laminate board at the intended location of the cut;
After that, the bar is installed on the machine in a horizontal position and down with a pattern.
The edges of the bar must be held tightly with your hands and slowly pushed away from you in the direction of the rotating disk.
When using saw blades on laminate, you need to be very careful not to hurt your hands. The sleeves of the outer clothing of the worker must be buttoned up, the disk is closed with a special casing.

The complexity of the whole cutting process is that the laminate saw blade is not designed for curved cutting. But this task can be easily handled by an electric jigsaw. Thanks to the use of this tool, you can make any curly cut.

When cutting laminate with a manual circular saw, it is important to know that the disk on it rotates from the bottom up, respectively, if it is not sharp enough, torn edges will remain on the material. To avoid this, when preparing the board for the cut, it must be laid face down.

Conclusion

In conclusion, a little about how professionals saw laminate. People who face daily similar work, most often use in their practice a special machine for cutting laminate. It has a very sharp blade that makes a precise and even cut. With it, professionals cope with cutting large amounts of material very quickly.

This tool is almost irreplaceable for the masters who are engaged in professional laying of floor coverings. In order to make the whole process more visual, you can view photos and video materials on this topic.

The decision to decorate an apartment or house with the help of such flooring is made daily by hundreds of people. For beginners, there is usually no question of how to install, since the laminate manufacturer provides detailed instructions and offers all the necessary Consumables. But to decide how to cut the laminate - home master happens to be difficult.

Full list of available tools

Today it is not difficult to purchase a laminate of any strength class. Differences in the material can be in the thickness, quality and strength of the protective and decorative coatings. There is also a difference in the main board, which provides rigidity.

They produce both a laminate according to the classical scheme, from MDF covered with several layers using lamination technology, and a one-piece vinyl finishing material, which has only one outer protective layer.

A complete list of how to cut a board of the right size () for laying flooring looks like this:

hacksaw for metal;
saw on wood;
jigsaw;
construction or clerical knife;
plastic knife;
grinder, she is also an angle grinder;
a circular saw;
special guillotine for laminate;
blade cutter.

Each of the devices differs in both accessibility and convenience and speed of work. The decision on the best way to cut a laminate is made on the basis of the requirements for the amount of work, the quality of the resulting cut, and also the accuracy of processing. If we are talking about a small repair and want to know how to cut the laminate at home, the list will be significantly reduced.

Hacksaw for metal and saw for wood

One of the tools of the home master. It is in almost every apartment or house, you can take it from your neighbors, in case of emergency - buy it at the nearest hardware store.

A hacksaw for metal allows you to get a clean cut without tearing off the decorative coating. And if a decision is made to use a saw for a tree, it is advisable to choose a tool for gardening, designed for cutting branches and knots. Work hand tool looks like that:

using a pencil or marker, the cut line is marked;
if you need a right angle cut, it is recommended to use a carpenter's marking corner;
first, a decorative and protective coating is cut through. This must be done carefully, minimally damaging the edges.

Then the MDF board is cut with a saw or a hacksaw. These tools are the most common option when deciding how to cut a laminate at home.

Electric jigsaw

The use of power tools allows you to achieve high speed and, with a certain skill, the quality of the cut. But when working with a jigsaw, you should follow some rules.

To make it convenient to work, the markings are done on the front side of the laminate board. In order to avoid tearing off the decorative coating during cutting, a saw with a reverse tooth direction is chosen. Standard - picks up material from below and can damage the upper layers of the laminate.
If it is not possible to use a saw with a reverse tooth direction, marking must be done from the back of the board. In this case, the decorative coating will remain intact at the edges of the cut.
At zero feed and high revolutions, special saws with a straight tooth can be used.
If you want to achieve very high precision and cleanliness of the material passage, it is recommended to use special thin saws for figured cuts.

They work with an electric jigsaw according to the expected pattern: they draw a cutting line depending on the type of saw and go through the material. The advantage of using a power tool is that you can make long cuts, for example, along a wide strip. This will require care or support along which the sole of the jigsaw will move.

Video on how to cut with a jigsaw.

Knives

A construction or stationery knife is a very successful tool for cutting laminate. You need to do this according to the following scheme:

after marking the future cutting line on the front side, a support is installed, preferably a metal corner or ruler;
blade with strong pressure is carried out along the laminate along the support.

It is necessary not to move the support and make several passes of the knife until the blade has passed more than half the thickness of the laminate board. After that, it is broken with a slight swing. It is not recommended to apply excessive force so as not to deform the edge with a decorative coating.

A knife for plastic (along with construction and stationery) looks like the answer to the question, what is better to cut. This material is quite plastic and easily lends itself to a steel blade. The special blade for plastic, thanks to the curved tip, allows you to make a deep cut without excessive pressure, helping to maintain a straight line.

Bulgarian or angle grinder

Rarely used tool. It is quite simple to work with them - the cut line is marked and passed by the disk. But there are also disadvantages. The laminate burns, dirt can form at the edges of the cut, the grinder is noisy and quite dangerous to use. In order to do the work quickly and at the same time qualitatively, skill and experience are needed.

A circular saw

A hand-held circular saw has an impressive list of advantages. Among them:

the ability to adjust the depth of cut;
high purity of processing;
acceptable noise level;
relatively low hazard indicator, controllability;
no smoke, no dirt - only fine sawdust.

To work with a manual class circular saw, you do not need great skills. The recommended course of action for beginners includes installing a reliable support for the movement of the sole of the tool and working on the table.

By adjusting the plunge of the saw blade, you can cut laminate without damaging the surface of your workbench or other support. Main disadvantage circular saw- not everyone has such a tool, it is irrational to buy it specifically for laying a laminate floor.

Guillotine and blade cutter

Two tools that are specialized. These devices work like this:

a strip of laminate is laid in the guillotine, with a cutting line directly under the blade. After that, pressure is applied to the working body with a long handle. The disadvantage of the guillotine is the short length of the cut; it may be difficult to cut a wide board at an angle;
a blade cutter is similar to a photographic cutter. Hybrid technology is used - both scissor and guillotine. The advantage of the blade cutter is the ability to make long passes of the material, which, with a certain skill, will allow you to process some dimensions of the boards along.

The guillotine and cutter are professional tools. They provide extremely high cleanliness and precision of cuts, allow you to process a huge amount of material with stable quality.

But the main disadvantage of a professional tool is that it is expensive, it can only perform one, precisely indicated operation. Therefore, it makes no sense for a home master to look for such devices for a one-time repair.

In practice, laying a laminate floor on your own can be done using a hacksaw. And if the performer's hands are strong enough and hardy, a construction or clerical knife will show high speed, cleanliness and accuracy of processing. Such a tool is sure to be found in any apartment or the nearest hardware store.

Anyone who has ever laid laminate flooring at least once knows that it is impossible to achieve a perfect finish without cutting it. After all, no matter how hard you try, you won’t be able to reach any of the walls and keep the full length of the planks.
Yes, and chess classics in a drawing cannot be observed without cutting. Laminate is not the kind of material that you can work with with an ordinary kitchen knife: not every tool is capable of making a cut with high quality. That is why, when starting to lay a laminate flooring, you need to decide in advance on the cutting unit. Perhaps it will be a discovery for someone, but there are many answers to the question of how to cut a laminate. Each of the tools has its own advantages, features, potential, operational nuances. And you need to know about all the subtleties, so that later, in the process of work, you can avoid several problems at once.

Tool selection

What can be used to cut laminate? Each master has his own criteria by which he chooses a cutter for panels. For some, its weight, operation from the mains or exclusively manually is important. Someone will choose from a variety of options the smallest tool, convenient and mobile. But for most craftsmen of any level, who are thinking about how to cut a laminate when laying, an ideal cut, the ability to quickly complete it, will still be important. We list all the tools designed to work with laminate boards, we denote the characteristics of each of them.

When asked how to cut a laminate, experts give at least 7 answers:

electric jigsaw;
circular saw;
grinder or machine for grinding corners;
hacksaw;
cutter;
construction knife;
with an ordinary utility knife.

With almost any of these tools, you can get an even cut. Naturally, if you have the appropriate experience of handling. There is no single recommendation on how to cut a laminate at home, what is more correct or more professional to use in this situation. Each master is guided solely by his own experience, practice. Therefore, we will begin to disassemble each of the above in order.

Power tools: jigsaw

This tool in most classifications is number one. There are several reasons for this. An electric jigsaw is an extremely convenient, simple, easy-to-use, very effective tool. Therefore, when looking for a solution to the problem, the better it is to cut a laminate, many stop on a jigsaw.

Even a beginner can use it, even women's hands can handle it. And the result will be more than high quality: the cut will be perfect, even, smooth, because the jigsaw gives out a large number of revolutions. The main thing here is to choose the right file. Usually in a set with a jigsaw there are accessories exclusively for laminate. They have a special shape, step, wiring of teeth. But an ordinary file designed for metal can also cut the boards: with small teeth of a narrow shape.

Important! To properly shorten the panel with a jigsaw, lay it on a flat surface with the wrong side up.

On the inside, you should do all the markings, that is, draw a cut line. How to cut a laminate if there is no jigsaw to get an equally perfect cut? You can use a circular.

Power tools: circular saw

This tool will really give a no less perfect cut than a jigsaw, but working with it is an order of magnitude more difficult. Therefore, picking up a circular should only be for those who have decent practical experience, or for those who have re-read, reviewed a large number of materials, how to cut a laminate. There are a lot of videos with this title on the net.

If the choice fell on the grinder, you should install a disk for metal. It cuts wood the best. Before cutting, the panels are fixed on a perfectly flat surface, but the wrong side in this case must always be on top. The disk in the process in the plank will not get stuck or slip. All movements should be performed smoothly, without haste, special pressure. However, skill is still required here. If there are no other options, it is better to practice on construction waste first before cutting the material needed for laying, which is called “filling your hand”. But if you still want to learn how to cut laminate correctly, but do not have experience with a circular saw, give preference to a jigsaw.

Power tools: grinder

When pronouncing the word "grinder", many will have one very strong association with metal cutting. Most first got acquainted with this tool when they changed houses metal pipes on plastic. However, this unit has great potential. Grinding machines are different sizes, capacities. Because of this, they have one main quality - versatility. Therefore, there is a certain category of craftsmen who do not have a question about how to cut a laminate. They automatically choose a grinder, because it is with her that they are used to cutting absolutely everything.

The grinder is very convenient to use, gives a perfectly even, smooth cut. To make it work, you need to install cutting discs:

metals;
concretes;
ceramic tiles.

Important! Planks should be stacked and fixed face up before cutting.

There are two things to be aware of when using this power tool. important moments: large amount of dust, bad smell scorched tree. If you are wondering if it is possible to cut a laminate with a grinder, the answer is yes. Just don't do it indoors. It is better to go outside or to the balcony.

Hand tools: hacksaw

If you are puzzling over which saw to cut the laminate with an electric jigsaw small quantities, an ordinary hacksaw can help you. The only thing to be prepared for is that working with such a tool will require some physical effort. In addition, it is a mistake to think that for cutting wood you should choose a hacksaw with large teeth for wood. They will only “tear” and crumble the plank, break fragments out of it. To prevent this from happening, you should choose only a hacksaw for metal - with small, often located teeth.

A hacksaw is not suitable as the main tool, so professional teams do not use it. The disadvantages of using the following: low productivity, high physical costs, the risk of material damage. But in some cases, when it is not advisable to cut the laminate with a grinder or a jigsaw, when the volumes of material are small, a hacksaw can be very useful.

Hand tools: construction knife

When laying laminate flooring, various situations arise in which you can be helped out ... by a simple construction or even a clerical knife. For example, just a couple of boards are left to trim or cut, a power tool is out of order, and the work needs to be completed. A construction knife is one of the tools, the use of which does not require skill or experience. However, they will need to cut with the application of physical forces. It can be used especially when it is important to quickly decide how to cut the laminate on the floor without long fixing the panels. The board is placed upside down. The cut is carried out along the ruler and with some pressure. It will not work to completely cut off the fragment: only a deep mark will remain on the surface. Next, you just need to press a little to break off the incised piece.

Professional tools: cutter

This tool has an impressive design, narrow application, since the cutter is used exclusively for working with laminate. This is a professional, rather expensive manual device that does not require any skills or physical strength from the user.

The cutter differs precisely in that it cuts planks like a super-sharp butter knife. Outwardly, it resembles a guillotine, so when cutting, you need to make movements from top to bottom. When, before laying the material, the question arises of how to cut the laminate, the cutter is almost the last thought, because due to its narrow specialization, not everyone knows about it. And after the efficiency and power of it cause sufficient surprise. Appointment "under the laminate" is not the only "minus" of the cutter.

Important! It is possible to work with a cutter with planks only in the transverse direction.

It does not cut panels along or figuratively, but it works quickly and simply.

Process details

Getting started with this material, you should not only know how to cut the laminate at home, but also how to do it correctly. We list only some of the points related to the basics of working with laminate:

in order not to crumble the edges, not to damage them, you should choose discs and saws with minimal and frequent teeth (for working with metal);
if damage occurs on the cut, such a board should be laid “under the plinth” so that it naturally hides the flaw;
before cutting, you need to double-check the calculations several times so as not to spoil the material;
to get a perfect cut on the front side - the boards need to be placed inside out down;
when cutting panels directly, no special efforts are needed;
figured cuts with a jigsaw should be performed using a template, gluing construction tape to the places of the cuts.

In conclusion, I would like to say: if you have even the slightest doubt about how to cut the laminate or whether you have made the right choice of tool, consult with specialists. Better yet, trust them to do the job. After all, not right choice tool can result in damage to the material, which is not very cheap!

Laminate - comparatively new material for flooring, but gained well-deserved popularity due to its practicality and aesthetic appearance. In addition, it is easy to assemble it yourself, after completing all the necessary measurements.

Laminate boards during assembly must be laid in a checkerboard pattern to give strength to the entire structure. Therefore, each row requires a correction in length, both at the beginning and at the end.

It is not so difficult to shorten boards or cut out pieces of a certain shape, the main thing is to make the right choice - how to cut a laminate at home. Consider what kind of tools can be used to cut a laminate board.

Hand saw: nuances of work, safety precautions

If the front of the work is small - one or two rooms - and there are no electric cutting tools, it is quite suitable hand hacksaw. The hand saw blade should have very fine and frequent teeth.

A hacksaw is best, since laminate is a hard, very strong, pressed material, and it is difficult to cut it with a conventional tool with large and rare teeth.

The laminate board is sawn from the front side, and in order to avoid chipping and chipping, masking tape must be glued along the cut line. On top of the tape, an exact line is drawn under the ruler or square, along which the material will be cut.

The electrocutting process will greatly facilitate and speed up the process, and the quality of the cut will be better. Using an electric or hacksaw, corner cuts can also be made in the laminate, but such tools are not suitable for rounded cuts (for example, under a pipe or arch column).

To cut the board, it is necessary to lay it on the desktop so that the cutting line is from the edge of the table at least 20 mm apart.

Cutting laminate with a jigsaw

The best tool for cutting laminate can be called jigsaw. It is quite comfortable and easy to use tool.

The main advantages of a jigsaw over other tools are:

compactness, small weight;

the ability to make a cut of any configuration (wavy, rounded with different radii);

simplicity, ease of use;

high quality cut without chips and cracks.

Cutting a laminate board with an electric jigsaw is carried out at high speeds, so the cuts are of high quality - both figured, and across the board, and along the entire canvas. The main nuance is the choice of a jigsaw file.

For sawing laminate, special files are intended with a special shape of teeth, frequency and method of divorce. Standard saw blade for cutting laminate with reverse teeth is marked T101 BR.

Video: How to cut laminate smoothly and without chips

The cut line is drawn on the reverse side of the laminate (usually the manufacturer indicates which side is best for cutting). Then the board is laid on a table or a special stand so that the part to be cut is outside the plane of the desktop.

The laminate board is pressed tightly by hand to the surface and the excess part is quickly cut off. The most important thing is to fix the board well so as not to damage it and avoid accidental injuries. In the process of work, do not rush, press hard on the jigsaw.

Circular saw for laminate work

If you don't have a jigsaw, you can use a circular saw to cut the laminate. This is a more complex tool, you need to have certain skills to use it. With the help of a circular saw, you can get the highest quality cuts of a laminate board along and across the canvas.

Cutting element - disc size 16-20 cm, with a web thickness of not more than 20 mm, the number of teeth - 48 pcs. When using this tool, you must follow certain sequence actions:

remove the protective cover, install and fix the cutting disc on the laminate;

using a goniometer, set the saw blade perpendicular to the lamella;

make markings on the front side of the panel and fix it so that nothing interferes with the movement of the saw;

cut off the excess with a smooth motion.

During cutting, the tool should be held strictly perpendicular to the laminate panels so that the cut is even, cut smoothly, without stops and jerks, since they are the cause of chips.

This cutting method has a rather significant drawback - a dusty cloud and the smell of burnt material. Therefore, you need to work on the balcony or in the open air.

Laminate cutter

Another one of the tools designed for cutting laminate is a cutter that works according to the principle of the guillotine. In other words, this is a sharp knife that, with the help of a handle, falls onto the board and smoothly cuts it. To work with the cutter, skills and the use of force are not required, the cut is very high-quality, even, without chips, and the process itself proceeds without noise and dust.

With the help of a cutter, you can easily achieve the perfect result. professional level. But it is advisable to use this tool for professionals, as it has a narrow specialization, it is intended only for cutting laminate. So to repair two or three rooms, it makes no sense to purchase this tool.

Another disadvantage is that it is impossible to cut the laminate panel along the web, but only across.

A lot of people, starting to repair their apartment with their own hands, simply do not know how to saw the laminate. As it turned out, the most convenient and easy to use tool is an electric jigsaw.

If you follow certain rules, you can quickly learn and achieve a good result. Each of the tools discussed above has some advantages over the others - the choice must be made in accordance with professional skills.