DIY turntable. How can I replace a cake turntable?

Baking cakes is not only interesting, but also responsible. The quality of decoration determines the aesthetic appeal of the confectionery product and the ability to arouse appetite among consumers. Therefore, without a special rotating round table, intended for decorating sweets, is indispensable.

The stand consists of several parts. Using step by step instructions, Rotary table for the cake you can make it yourself.

Why do you need a turntable?

A rotating cake table is a great find for those who are interested in baking complex confectionery products.

The device has the following advantages:

  • significantly facilitates the final processing of the cake, rotating around its axis;
  • the pastry chef can decorate the product without moving, which greatly speeds up the cooking process;
  • Often there are special markings on the table surface that allow you to create smooth and neat elements.

The rotating stand will help professional confectioners and ordinary housewives create culinary masterpieces.


Features of choice

To avoid making a mistake when choosing good table, it should be assessed according to several criteria.

Rotation mechanism

The most important part of the model, without which the table simply will not spin, is the rotation mechanism. It is a metal bearing located under the table top, ensuring it rotates evenly around its axis.


Diameter

The most common tabletop diameter is from 26 to 30 centimeters. The cake has these parameters standard size up to four kilograms.

But for convenience, it is better to choose a larger diameter so that you can rest your hand with the palette on the tabletop while working. This will help achieve a more accurate result.


Silicone feet

Required part, designed to fix the structure in one place. This prevents the confectionery product from sliding on the surface of the countertop, thereby eliminating possible defects and damage to the cake during processing.

Such legs are quite inexpensive, around a few hundred rubles, but thanks to them the product will turn out perfectly smooth and without damage.


Marking

On the round surface of the tabletop there are special divisions that divide it into equal segments. This is markings that help create decorative parts that are completely even and identical in size. In addition, parts of the cake will be located under right angles, which will definitely ensure a high-quality final result.

If there are no markings, you can apply them yourself using a ruler and compass.


How to make it yourself

The modern market offers many devices to make baking easier. However, by making a cake turntable yourself, you can save a lot of money. Besides homemade design can be created from your own materials, adapting it to specific requirements.

Required tools and materials

To create a model you can use various materials. The most common options are wood, plywood, chipboard.

For work you will need the following tools and materials:

  • pressed bearings, 2 pcs.;
  • lumber;
  • thin plastic;
  • metal circle;
  • tubes made of plastic or metal;
  • nails;
  • self-tapping screws


Further instructions will be devoted to how to make a rotating cake stand with your own hands from plywood, as this is the most convenient and inexpensive option.

Manufacturing

Before starting work, you should make a drawing, indicating on it the parts that will make up the model and their dimensions.


Creation instructions:

According to the drawing, two circles of the required diameter are cut out of plywood - 20 centimeters.


A bearing is inserted into one of these circles. The hole for it is cut out in advance.


The two parts are twisted and fastened using self-tapping screws, and the bearing is inserted into the center.


The upper and lower parts of the table are connected using plastic tubes; if desired, metal ones can be used.


They must fit very accurately into the bearing. The most optimal length of the tube is 15 centimeters. The upper part of the model is made of metal. Her size plays a big role important role, so it’s best to make the diameter 30–40 centimeters.


Then the parts are connected to each other using a welding machine. You can also use hot glue for fastening, which hardens when cooled. Next, the rotating circle is placed on the pipe and fastened with self-tapping screws.


The finished table is decorated in different ways. For example, the surface is decorated with crepe paper or thin plastic.


Video

Watch a video about making a wooden turntable with your own hands.


There is such a thing as a turntable. Some people use it for presentations or souvenirs. Confectioners use it to rotate the cake while making it. I decided to make a turntable with my own hands to display my homemade products, like in “3D”. It was based on a motor from microwave oven. Makes almost 3 revolutions per minute. Powered by 220V household network.

To design the table we will need:
- circle made of plywood;
- a rectangle made of plywood;
- switch;
- aluminum corner for mounting the switch;
- power cord;
- screws 10 pieces;
- a motor from a microwave oven.


The first step is to make a cut in our base for the motor. It turned out somehow crooked, but that’s not the point, it will be covered by the table itself. Base dimensions 250mm*100mm, plywood thickness 18mm.


In the table pancake we drill a hole with a diameter of 6 mm, the motor axis is 6.5 mm. The hole is not through, but exactly the length of the motor axis (about 10 mm). Let's try it on. Fits tight. If you drill with the same diameter as the motor axis, the table plate will dangle. It will have to be glued, and this will add additional time to making a homemade product.

You definitely need to look at the motor. They are not 220V. I came across 21V. In the latter case, a transformer is needed; it can be powered from the control board of the same furnace.


Since I have used plywood, I decided to spray paint the pancake and the base of the table. Matte black paint was available. Everything dried quickly. At the same time, I drilled a hole for threading the wires through.


After the paint has dried, screw the motor into its permanent place. I took the screws from an old printer. Very successful because of the wide cap.


We thread the wires into the hole from the bottom of the structure. We solder the switch, for me it is a toggle switch TP 1-2. We attach the corner to the base. We screw the toggle switch to the corner. If you don’t have a corner like I have and another switch, then you can make something to suit your needs.


To prevent the structure from moving on the table, I decided to install rubber feet. I used medicine caps as legs. In general, it is very convenient to use such legs in the manufacture of cases and homemade products. Rubber is very elastic. I screwed them onto the same screws from the printer.


The table plate in my case is 230 mm. The thickness is still the same 18 mm as at the base. Suitable for my needs. This is the table I got. I repeat, it makes almost 3 revolutions in a minute.

I have had a large round table in my living room for many years. Friends and relatives often gather for a festive feast. During the meal, requests arise to pass on this or that dish. This causes unnecessary fuss and certain inconveniences. After looking at a lot of information on the Internet about different models furniture, I decided to make a rotating table with my own hands, the drawings of which I completed myself. Having assembled a simple design, I immediately got rid of the above-mentioned problems. In this article I will tell you how to make a round table with a rotating center with your own hands.

Tabletop project with a rotating center

It was important to me to create a stand in the form of a turntable. Its design should be simple and not cause time or financial costs. The main idea is the design of the table plane rotation unit. I used a hinged furniture support. I decided to make a load-bearing plane from two sheets of fiberboard and chipboard. I don't use wood. Before making a table with a rotating center with my own hands, I prepared the tools and materials.

Tools

Having assessed the volume and types of work, I collected tools in accordance with the following list:

  • jigsaw, which I use to cut circles from fiberboard and chipboard;
  • I will need an electric drill to drill holes for connecting furniture parts;
  • screwdriver for fastening screws;
  • an air compressor with a gun for blowing holes and treated surfaces;
  • hammer;
  • iron;
  • wrench;
  • improvised tools (pliers, screwdriver, metal ruler, tape measure, knife, pencil).

Materials

To make a round table with a rotating center with my own hands, I selected the materials necessary for this. The list included the following:

  • fiberboard sheet – 600 x 600 mm;
  • piece of chipboard – 600 x 600 x 20 mm, selected according to the color of the main tabletop;
  • roller support;
  • a piece of timber 50 x 50 x 500 mm;
  • hardware – 4 screws 6 x 20 mm, two bolts 10 x 30 mm with, one screw 8 x 70 mm washers and nuts;
  • Whatman paper;
  • liquid nails – tube (185 g);
  • end adhesive furniture tape 25 mm wide;
  • sandpaper.

To make it clearer to the reader how to make a rotating table, I have compiled instructions for assembling this device.

Step-by-step instructions for assembling a rotating table with your own hands

I outline all my actions in points in the following order.

  1. I determine the size of the rotating plane to be 600 mm. Since the diameter of the main table is 1300 mm, the table will not interfere with the plates around it.
  2. I fasten a sheet of whatman paper to the board with push pins.
  3. Using drawing tools, I draw a 600 mm circle on paper. I carefully cut out the table layout with scissors.
  4. Having attached whatman paper to a sheet of fiberboard, I trace it with a pencil. I use a jigsaw to cut out the lining for the tabletop.
  5. I perform the same actions with a piece of chipboard.
  6. Using pliers and a screwdriver, I remove the plastic roller from the metal hinge.

  1. In the middle of the block I make side cutouts for a tight installation of the support.
  2. Having installed the hinge strictly in the center of the beam, I drill a hole from the side through the openings in the metal.

  1. I apply the hinge area to the center of the fiberboard and mark the attachment points with a pencil. The hinged support will allow the table to rotate and turn in the desired direction at any time.
  2. In the fiberboard, following the markings, I drill 4 6 mm holes with a drill.
  3. I thread the screws through the holes in the sheet and support. I put washers on the side of the platform and tighten the nuts.

  1. I coat the screw heads with machine oil.
  2. I apply a circle of chipboard so that the outer boundaries of the two circles coincide.
  3. Using the marks obtained, I use a drill to make small indentations in the chipboard. They will allow the screw heads to not interfere with the tight fit of the two parts of the rotating tabletop.
  4. I apply a layer on the surface of the chipboard liquid nails and connect both parts of the table. Having separated them, I wait 3 minutes. Then I finally connect the parts, loading the top with heavy objects at hand.
  5. I sand the side edges of the circles with sandpaper.
  6. I place the support beam in the center of the round table. I make marks at a distance of 30 mm from the edges of the plank.
  7. I drill through the marks through the timber and the table top.
  8. I thread two bolts. At the bottom of the tabletop I secure the bolts with nuts and washers.
  9. I put a hinge with the table top on the fixed support beam. I thread a bolt through a pre-drilled horizontal hole and tighten it with a nut and washer.
  10. I glue the tape along the end of the circle using an iron. I cut off the protruding part of the edge with a knife. The table is ready.

This instruction makes it possible to understand how to make a table with a rotating center with your own hands without much hassle and at minimal cost.

Labor costs and cost of making a table with a rotating center with your own hands

After finishing the work, I was interested in calculating how much it cost to install the rotating table. Money was spent:

  • Fiberboard (0.5 m2) – 50 rubles;
  • Chipboard (0.5 m2) – 100 rubles;
  • liquid nails “Montazh” (tube 185 g) – 160 rubles;
  • articulated leg for a chair – 70 rubles;
  • sheet of whatman paper (1 sheet) - 20 rubles.

Total: 400 rub.

I bought sheet material from a furniture workshop as cutting waste. I took a piece of timber, hardware, and adhesive furniture tape from my supplies.

As for labor costs, the work took me no more than 8 hours.

DIY rotating table


After making my own turntable, I came across plans for an easier turntable project. You can use a hinged support with a vertical axis instead of a platform. This should be done as follows:

  • a hole is drilled in the center of the round table,
  • insert an axle with a plastic insert into it.

The table is assembled and attached to the rotating support in the same way as described above. What is attractive about this method of creating a round table with a rotating middle with your own hands? Because the table can be removed at any time, and the hole in the center of the table can be closed with a plastic plug.

DIY rotary positioning table.

Another very useful tool was added to our workshop with the unusual structure we made this time. This rotary positioning table can be useful for a wide range of structural fabrication applications.


This table is capable of rotating the metal plate from 0 to 100 degrees with the rotation speed already adjusted. This may seem quite simple and gimmicky, but imagine having to manage a stable weld while the part is rotating at a gradual speed. I can assure you that the welding will be automatic and much more uniform. It would be equally easy if we placed the router in a stable place, rotating a piece of wood, we would immediately get a perfectly shaped cut wooden circle. Moreover, it would also be easy if we had a plasma cutter while rotating the metal plate. These are just a few of the many spreadsheet-specific utilities that use your imagination, and their functions are countless.

Step 2: Gearbox - DC Motor











It all started when a friend gave us a gearbox that can do 10 rotations in just one. Then we found the engine direct current from an old trainer and connected it to the gearbox. Therefore, the motor using a speed controller can rotate from 0-3000 rotations, so when it was connected to the gearbox, it rotated from 0-300 rotations. From the gearbox we managed to make a 65 cm axle, onto which we applied metal plate, and this is also the surface of our project. This axle is also supported by two more bearings for even greater durability. Since the already mentioned parts were connected, they were placed on a 40mm thick axis, which can rotate all parts made from 0 degrees to 100 degrees. By using a crank and a threaded shaft (screw threads start on one side of the shaft and extend to the other side), we have created a system that when the crank rotates, it rotates the entire system, resulting in a tilt that we need to work with. All this moves on a metal base, which was made from square pipes with dimensions of 50 mm x 50 mm x 2 mm. On this metal base we have also placed a mechanism that plays a role when the position is selected and it is suitable for working and tightening the bolt, the table is stabilized completely and securely.

Step 3: Design




One of the advantages of our own table design is that when it is placed in a horizontal position at an angle of 0 degrees, there are two surfaces to work on, one on the front side and the other on the back side table. Specifically, on the back side you can have a chuck and be able to fit smaller objects, and on the front side, where there is more surface to work with, you can fit larger objects.
The motor that was placed to move the table left and right uses two contactors that are activated by pressing two steppers. The steppers are made of sheet aluminum and their covers are made of sheet metal. In addition, above the steppers there is a board on which the switches are located. One of the two switches is for emergency situation if a problem occurs, and it can be pressed to disable any function in progress. While the other must activate the entire mechanism and the potentiometer located next to it, it regulates the speed of rotation of the metal surface of the work. Regarding the future use of the structure, various bases can be placed on which a variety of support tools and machines can be placed, increasing the potential use of our structure. Final, Thus, we managed to implement another team project to make it extreme with great success. This way our workshop is one step ahead by being more fulfilling.

Step 4: Video

We believe that the particular framework was worth our time and effort, not only for the satisfaction gained from creating it, but also for the great utility of the particular tool.

It is very convenient for confectioners who make cakes to use various types of devices that facilitate the process of decorating the finished product. Fortunately, today stores offer a wide range of similar equipment. One such device is a turntable. True, the cost of such a table is quite considerable, and it is often easier and more profitable to try to make a turntable for a cake with your own hands.

How is it convenient?

This table will be useful not only for professional pastry chefs. It will be very useful both for those who like to cook for pleasure, and for cooks taking their first steps. This table will come in very handy for housewives who decorate cakes with fondant. It looks like a circle-pedestal on a leg that rotates around its axis. The main goal is to make the pastry chef’s work as ergonomic and convenient as possible, and to simplify the task of decorating the finished cake. The cake is placed on a stand, and by rotating it, you can easily cover it with fondant, decorate it with figures, inscriptions and other decor. You don't have to walk around it, pastry will rotate on the stand, and the hostess will have access to any place on the cake.

What you need

In order to make a cake turntable with your own hands, you will need:

  • Bearings - 2 pcs. It is better to use double pressed bearings.
  • Wooden blank for a circle. This could be the door from old furniture or any chipboard material available.
  • Nails.
  • Self-tapping screws.
  • Tube (plastic or iron).
  • Circle made of iron (metal).
  • Plywood sheet.
  • Plastic or decorative self-adhesive film.

How to make a turntable with your own hands

This process is not too complicated, but requires male participation. First, you should draw a drawing of the future stand and prepare everything necessary elements.

If the bearing is not double, then two will be required, and one must fit into the other.

  1. We push the smaller bearing into the larger one using nails.
  2. Using a jigsaw, we cut out two circles with a diameter of 20 cm from a chipboard blank (or an old door).
  3. In one of them, a hole should be made in the center into which the bearing is placed. It is this technique that will ensure the rotation of the entire mechanism.
  4. We attach the second circle with self-tapping screws (you can use liquid nails) to the first.
  5. The bottom circle, which does not have a hole, will stand directly on the table.
  6. Then a plastic tube is inserted into the bearing (an iron tube can be used, if available). It will connect the base and the top - the pedestal for the cake. The tube must fit very accurately into the bearing so that it does not dangle, otherwise it will be difficult to use the turntable. The optimal length of the connecting tube is 15-18 cm. In this case, it will not be too short or too long, and it will be as convenient to use the device as possible.
  7. The top (the stand itself on which the cake is placed) is best made of metal. You will need a metal circle with a diameter of 30-40 centimeters. It is attached to the top of the tube (metal or plastic) by welding. Of course, not everyone has it on hand at home. welding machine and a person who knows how to do it. In this case, you can use cold welding, reminiscent of plasticine.
  8. Plywood or chipboard, equal in diameter to the metal circle, is attached to the top of the metal circle using liquid nails or self-tapping screws.

Now the DIY cake turntable is almost ready. All that remains is to add aesthetics to it. To do this, the top is covered with wallpaper film or a plastic round base. This will give the device a finished look and make it easier to maintain.

As you can see, if you want, making a turntable for a cake with your own hands is not so difficult. A set of materials for its assembly can be found in almost any home, and the work process itself is not that complicated.

How can I replace a cake turntable?

What is the solution for those who do not have a turntable? Very simple and affordable solution also found in almost any home. You can use a rotating plate from the microwave. Almost all models are designed in such a way that they have a glass plate and a round stand at the bottom. You need to remove the plate and the circle underneath it from the microwave. If it is too smooth, you can put paper (a paper towel) underneath to reduce slipping. This way you can decorate the cake by smoothly rotating it around its axis. Also, a glass plate will not spoil the view when serving the finished decorated product.

Related publications