home Wooden

Make a mobile beer bar with your own hands. Home minibar - photo of cool and spacious counters. Mini bar made from scrap items

Our version of the mini bar is quite simple to manufacture, compact and spacious. It holds a lot alcoholic drinks, and there is also space for glasses and even glasses. In order to do DIY mini bar you will need the following materials:

MDF;
screws;
glue;
dye;
putty.

Tools:

saw;
jigsaw;
screwdriver;
drills (30 mm, 22 mm);
clamps;
sandpaper.

Step 1: Planning

This is the most important part of the entire project. The first step is to decide what we want to place and store in the bar:

wine bottles (~8 pieces);
bottles of low-alcohol drinks;
corkscrew;
wine corks;
cutting board;
wine glasses;
cocktail glasses;
glasses.

With such a list of requirements, we began to think about the size of the minibar. The width was set at 607 mm (internal), and the depth was determined by the length of the wine bottle, which should fit horizontally inside the bar.

For this project I bought 9 mm MDF sheet - 2440 x 1220 mm. Here is an approximate plan for cutting this material:

top: 340 x 607 mm;
bottom: 340 x 607 mm;
2 sides: 460 x 340;
2 front doors: 440 x 303;
rear: 440 x 607;
2 vertical partitions: 440 x 320 mm;
2 internal horizontal partitions: 607 * 320 mm.

It also took quite a lot of scrap wood to make the wine rack.

Step 2: Create a wine rack

To build a wine rack for 8 bottles, you need to cut 16 - 300 mm strips of spruce, they were approximately 20 mm thick.

The next step was sanding and making 45 degree cuts on the ends (purely for aesthetics). 4 strips for attaching to one of the side parts (460 x 340 mm) were spaced vertically at intervals of 110 mm. The first strip was attached to the bottom of the 9mm sheet. Similarly, the 4 remaining ones should be attached to one of the inner parts of the post, however this time the first strip should be placed on the bottom. The remaining 8 need to be screwed back to back onto another piece. To do this, I used two strips 50 mm wide, 9 mm thick, and 440 mm high.

Step 3: Glass Rails

Given the limited internal space, the desire was to make the glass holder as narrow as possible, but still be able to hold 2 glasses side by side. In order to select the optimal placement, we purchased glasses and experimentally managed to determine how to fit them into our minibar.

After that, we cut 607 * 320 mm strips and, after drilling a 10 mm hole, we cut out slots for the rack. At the end of the process, it was discovered that the slots needed to be made a little larger, so it was better not to reduce the width of the slot.

Step 4: Assembling the body

Now we take our wine racks and cup holders and all the materials we cut earlier and complete the entire structure. Given the thickness of the internal partitions, at this stage it was also decided to add slots in the sides of the bar for handles. To do this, I found a suitable place (where the wine racks are) and drilled two 30mm holes located above 55mm from the bottom of the structure, using a jigsaw to cut out the necessary holes. When all the holes are prepared and cut, all that remains is to connect all the parts of the bar together.

Step 5. Making a drawer

You can build a box from 5 pieces of MDF, cut to the required size. In our case, the width is 215 mm and the depth is 40 mm. We make a small cut in the middle with a jigsaw; it will serve as a handle for opening.

Step 6. Continue assembly

To finally assemble the bar we use glue and screws. Attach the top and bottom boards to the sides. Form a central section (horizontal shelves, glass holder and vertical partitions). This was done by placing the bottom 340mm board above the bottom, the top shelf ~50mm below the top giving about 30mm for cutting board and the cup holders are about 20mm below the top of the bar. Insert the inner part. Add right side. Add a wine cooler to the centerpiece. Add the left side.

To install doors, you need to slightly reduce the pre-prepared pieces under the door in height to fit them inside the gap and in width it is better to remove 2 mm on each to ensure comfortable opening (although this parameter will vary depending on the hinges used).

Then we insert the hinges (which we cut to the required length using a hacksaw) and first screw the hinges to the doors, and then all together to the bar. After this step, the doors and the entire minibar can be painted. We used two coats of paint and also made the front of the doors black.

Step 7. The minibar is ready

All that remains is to fill these holy bins with essential attributes: vodka, gin, rum, Cointreau, vermouth, ameretto, etc., as well as cider and wine. The wine cabinet holds 6 bottles, there are also 4 beer glasses, 6 shot glasses and a shaker. The drawer is quite spacious for storing a corkscrew, wine corks, a knife and other accessories, the presence of which is a must in any good bar. So now you have everything at your fingertips and in one place, you can use it for your health.

An older version of the same minibar. Restoration.

Anyone who has at least once made something in the house, or assembled furniture, can make a beautiful minibar with their own hands. A novice carpenter should not take complex designs - you can create a unique area for storing alcoholic beverages by just connecting several boards. In today's publication, the Homius editors will talk about simple ways creating a home bar.

PHOTO: remontt.net

Minibar "Globus" - a non-trivial and interesting solution for storing and serving alcohol at home. The diameter of the ball can reach 50 cm. You can choose the size that suits you. The easiest way to make such a globe-shaped storage system is to use a ready-made ball and varnish it.

The wooden minibar consists of a bowl, legs and a small chest of drawers. You can look for a beautiful globe in brown shades at flea markets on the Internet. Making a globe bar with your own hands from scratch is extremely difficult; for this you need not only special equipment, but also the appropriate skills.

Tools that will be required to create the product:

old globe;
three balusters;
plywood;
paint – brown, gold or silver;
fasteners;

To get balusters, you can disassemble old ones or chairs.

PHOTO: static.turbosquid.com

PHOTO: 9.allegroimg.com

PHOTO: 8.allegroimg.com

Minibar for the home: why is it needed?

Almost every man dreams of installing a bar in his apartment. This item decorates and gives the living room an unusual look. It doesn't matter what material is used. An old globe is painted with varnish, but a new one can be artificially aged or even simply left in its original form. A bar cabinet for the home is used as a storage facility for elite alcoholic beverages.

Bar functions:

the highlight of the interior is a hidden piece of furniture in which you can safely store alcoholic beverages;
storage of wine bottles;
cooling drinks at correct location cabinet;
storage of glasses and glasses.

To make your home look more solid, you can put a cabinet for storing wine drinks in the living room. At the same time, you don’t have to buy an expensive item in a designer store; you can make it yourself. The cabinet may have different shapes: globes, canisters, shelves with recesses for glasses.

PHOTO: img1.etsystatic.com

PHOTO: racetho.com

PHOTO: i11.fotocdn.net

How to make a minibar with your own hands: tools and materials

To make a cabinet for alcohol, you need to choose the right material. For assembly, you may need treated wood, such as ash, oak, cherry, walnut and Karelian birch. A friend or boss will be delighted with such a gift, since the cabinet is made of natural material is durable and stylish design. You can even make a bar in the living room from old boards, if you go over them with sandpaper and varnish.

To make a home bar with your own hands, you need to prepare the following tools:

varnish for covering boards;
metal corners;
solid wood boards with a thickness of at least 20 mm;
plywood sheets;
wooden block 30×30 mm²;
fastening parts.

When choosing wood, you need to give preference to those bars that do not have chips or nicks.

How to make a home minibar in a suitcase

The easiest way to choose a home bar for drinks is to look at the furniture options shown in the photo. To store alcohol in a beautiful cabinet, you don’t have to buy it; you can make it yourself, following the instructions.

Illustration	Description of action
	We take a log and cut it into equal parts, or use ready-made boards
	Divide the workpiece in half, grind the central part
	Remove the bark using a spatula
	We measure the size of the bottle so that it fits freely into the future suitcase
	We draw a straight line in the center of the workpiece and cut the tree into two parts
	We attach the holder to the two prepared bars. To do this, we scrape out holes the size of the sides and secure them with screws.
	Check to see if the workpiece closes tightly. We put it aside and process the remaining pieces of wood that will be used to create the lid and sides of the suitcase
	We assemble two blanks - the upper and lower parts of the structure
	We cover the bottom of both blanks with velvet. Cover the lids with varnish
	We take leather straps and secure them in the box so that the bottle can fit
	We also attach straps for three glasses
	We transfer the image onto a board or thick cardboard and glue it to the base - one of the sides of the suitcase. We assemble the entire structure
	We cover the edges with leather strips
	Additionally, we make loops on both sides of the suitcase in order to close it

To ensure the assembly goes smoothly, you need to try. Some errors can be corrected during the manufacturing process of the product.

Related article:

: purpose and types, how to make it in loft style, construction made of wood, stone, drywall, folding bar counter, step-by-step manufacturing instructions various types bar counters, photo examples of bar counters.

Home minibar from a canister

Before you make a bar from a canister, you need to find a suitable blank. The most difficult task during manufacturing - cutting the canister. To do this, use a circular saw. Then the product is processed so that the cuts are not sharp.

You can make a minibar from a canister with your own hands if you have the following tools and materials:

large canister, at least 20 liters;
wood screws;
rubber compressor;
rivets, loops and latches;
one thin plywood;
glue for processing windshields;
paint in a can;
colorless primer for processing the structure;
incisors;
a circular saw;
bits and drills.

A minibar made from a canister is not the easiest option, so you should start creating a product only after a little training, or if you have experience in metal cutting.

Tabletop minibar

To make a bar cabinet for the living room, you need to follow simple instructions, after selecting high-quality material. To make storing bottles convenient, it is recommended to make a small, mobile design.

Illustration	Description of action
	Saw the board into 8 equal parts
	We process the surface. The board should be smooth, without burrs
	We make markings for cutting holes. Every 10 cm intersect with a 1.5 cm cut. The width of the cut should match the width of the board itself
	Cut the holes and start assembling the structure
	We assemble a tabletop box for storing bottles gradually. After the structure is assembled, the boards are varnished

This storage shelf option fits perfectly into any interior from classic to loft.

We will send the material to you by e-mail

You can make your own minibar from any available material. Various boxes, deep forms, canisters and much more will serve as the basis. The editors of HomeMyHome in today's publication will talk about the configuration and production features of this miracle device. It turns out that this little thing can be very useful.

The minibar can store not only alcoholic drinks, but also soft drinks, as well as some dishes
PHOTO: masterclub.online

Design of this product can be both complex and simple. For example, sometimes the owner of the house cannot pick up suitable option to match the finished interior. Perhaps there are too many departments inside or, conversely, the compartments allow you to store something that is not at all what you need. Therefore, there is a desire to make a bar yourself. Let's decide why it is still needed:

This design attracts attention wherever it is located. Sometimes not everyone can guess what's inside. Accordingly, such a specimen in the room plays an aesthetic role.
The device is designed for storing expensive alcoholic drinks or refreshing invigorating cocktails. They are relevant at business meetings and holidays when guests gather in the house. It is irrational to store drinks in the refrigerator.
Even homemade wine will not spoil if stored in a dark place. As a result, the taste of the drink from the correct content will only be better, more interesting and more refined.

Of course, a minibar in the house will be in great demand if at least one of the listed factors is present. It is important that the design has several shelves and compartments for placing bottles.

PHOTO: kreuzwortraetsel.me

Features of the minibar in the apartment

When trying to create a beverage storage structure yourself, the question of size and design arises. Typically, an apartment does not require a bar that is too large. Agree, it would be inappropriate to install a structure in a room that is completely inappropriate in design. As for the design features, they try to dwell on several points.

PHOTO: pinterest.nz

Equipment

There should be a sufficient amount of equipment inside the bar for ease of use. Therefore, you still have to spend money and buy the following parts:

shaker;
jigger;
muddler;
Steiner;
bar spoon.

In case these elements are present in the kitchen, you can do without them, but it is better to create a separate set for the bar cabinet for the living room.

PHOTO: podelki.org

As for the standard set of wines and drinks, only those products that do not require low temperatures can be stored in the bar. Among them may be red and white dry wine, live beer, homemade liqueur, longers, aged cognac and whiskey. It is always allowed to dilute this assortment with soda in tin cans.

PHOTO: gtrltd.biz

Location

A cabinet for alcohol can be placed in any room. More often it is installed in the living room, hall, hall and other rooms where guests are received. If the structure is small and hanging, then it can be placed on a wall where there is no decoration. Perhaps it does not perform any decorative function at all.

PHOTO: crumbsdoughnuts.com

There are bars that are effectively located in the corner of the living room. Such models have an angular design and can be distinguished by a rectangular frame, while the storage niche itself will resemble the shape of a ball or circle.

On a note! When making a mini-cabinet for alcohol, you must first decide on the place where it will be installed. Based on this, the size and shape of the structure can be determined.

PHOTO: tytmaster.ru

How to make a minibar

To create a beautiful wine rack you will have to work a little, but first you need to decide on the choice of option. Each of them has its own separate instructions. Let's take a closer look at each type of bar.

PHOTO: pinterest.ru

Floor bar-globe

Despite unusual shape, creating a globe bar with your own hands is not difficult. To make such a storage you will need a large globe, plywood or thin board, a jigsaw, and a locking element. Work is carried out according to instructions.

Take the globe and remove unnecessary parts from it: the axis and other components. Cut it in half with a jigsaw.
Measure the diameter of the cut and cut out exactly the same circle from plywood, make cutouts for the bottles in it. They can be made in different shapes.
Be sure to cover the sections with electrical tape. This will prevent further cracking and destruction of the material.
For the lower part, cut a circle with a smaller diameter than the first shelf. It will serve as a support for the bottles.
Make a latch on one side and install a loop on the opposite side.

PHOTO: globusoff.ru

All that remains is to attach the globe to any wooden frame. A regular one can also be used for this. coffee table. You can also create a custom version of the floor stand with additional tiers of wooden beams and build a mini bar counter. They can later be varnished or painted. This frame is assembled with the help of small nails.

PHOTO: rozetka.com.ua

Tabletop minibar

You can build a table-top home bar with your own hands different ways. For this, improvised materials are used.

Minibar for home in the form of a barrel

All you need to get started is old barrel small size, Sander, paint, tape. This will be an excellent alternative to a minibar made from wood yourself.

Illustration	Description of action
	Remove one ring from the barrel and sand the wood thoroughly. Then put the top ring in place and do the same with the bottom of the barrel.
	We cut off the excess parts of the boards near the lower and upper rings, sand the sharpness and burrs
	We screw in the screws to strengthen the rings. Next, we cut a hole using a jigsaw in the middle of the barrel. Sand all the rough edges again
	We clean the inner walls, then cover the wooden body of the barrel with mounting tape, without touching the rings. Coloring metal parts from a can
	We paint from the outside and inside future minibar
	We take a thick board, maybe chipboard, and cut out a circle from it with the same diameter as the inside of the barrel. We insert it inside and secure it with self-tapping screws
	On narrow bars we make holes for the bottom and neck of wine bottles. Then we paint these parts
	We cut the stands to size and insert them inside. You can arrange niches in one or two rows

Home minibar inside the cabinet: video

This section is for those who do not want to bother searching suitable materials to create a cabinet for storing alcoholic beverages. Let's look at how to make a bar cabinet for your home in the video below.

Minibar from a canister

To make a minibar from a canister with your own hands, it is better to use a metal structure that has not been used for a long time. Alternatively, you can buy a new one. The accessory is made according to the following algorithm.

Prepare the necessary equipment: grinder, screws and screws, latches, seals, interior lining and other materials that may be interchangeable.
Measure the future door and cut it with rounded corners; use a nylon cover for this.
Glue a rubber seal around the entire perimeter of the cut edge. It will serve for safety and tightness.
Install the rivets on the side where the door will open, inner space Paint the structures dark.
Additionally, it can be sheathed with any comfortable material: remnants of lining, wood or plastic.

PHOTO: vsesamodelki.ru

By doing interior decoration Keep in mind that the structure should not be too heavy, otherwise you can forget about mobility.

Minibar for alcohol inside the suitcase

To restore “grandmother’s” suitcase for travel, you will have to use various options decor, locking devices and much more. This storage can be large, used permanently, or small - portable. We offer several interesting options for decorating a bar for your home with your own hands.

PHOTO: novate.ru

PHOTO: hipsterpride.me

Interesting design ideas for minibars with photos and descriptions

In addition to the main types of bars, you can make other equally chic options. Many of them have excellent functionality and help store various things, including alcoholic drinks.

PHOTO: hipsterpride.me

To create such a bar for your home with your own hands, it is recommended to use reinforced plastic material. It is more rational to make a retractable tabletop for this design from wood of sufficient thickness.

We often like to create coziness in our home with our own hands. This applies to many things: from creating jewelry to self-assembly furniture and electronics. Indeed, when you do something yourself, much less money is spent on it, and the result will depend only on you and your efforts. As suggested, it is much more convenient and efficient. So, today we will talk about how to make a minibar with your own hands so that it matches the interior, surroundings and our own mood.

A little history

The concept of “bar” has firmly entered into everyday life and is used throughout the world thanks to America. It was there that the owners of public alcohol establishments were the first to realize that they would not earn money if visitors sat for a long time on comfortable chairs with one mug of beer in their hand. Enterprising Americans put up a so-called barrier between visitors and stands with alcoholic drinks, and instead of comfortable low stools they installed high chairs to sit on. for a long time It was impossible, because people, having ordered drinks, quickly left and made room for new customers.

Over time, the word “barrier” has become obsolete in everyday life modern people Only the concept of “bar” was included. Along with the original name, the purpose also changed. Nowadays, a bar is not so much an establishment where you can drink, but a certain area in the house where characteristic drinks are stored. This is a bright and at the same time practical interior detail, showing the well-being of the home.

Types of bars

Before you make a minibar with your own hands, it’s worth determining what types it comes in:

A stationary bar, that is, one that has its own permanent place, is suitable for you if you constantly host a large number of guests. Such a bar often occupies an entire room and includes special furniture, glassware for drinking and making cocktails, a large number of shelves for alcohol, refrigerators and display cases.
A mobile bar, or otherwise a minibar, can be assembled if it is not possible to allocate an entire room for these purposes. Most often, a minibar is a cabinet with an air conditioning system that is used to store alcoholic beverages. It can be purchased at furniture stores or made independently from scrap materials. However, with a little analysis, anyone will come to the conclusion that it is better to lean towards the second option, since it is cheaper and more convenient in the sense that you can figure out what it will look like and where it will be located.
A bar on wheels is a type of mobile bar. Such a device can be stored in some closed place and taken out only when necessary. This minibar is suitable for residents of houses with limited space, but who really want to have such an invention.

Where should the minibar be located?

If you still decide that you need a mobile bar rather than a stationary one, then the next question in line will be where to place it. Here you should turn on all your imagination and go in search of interesting places in a house in which, purely theoretically, it is possible to place a mini-bar. These could be:

places under the roof;
unused niche in the wall;
unoccupied space under the stairs;
balcony or loggia.

Before you study in detail how to make a minibar for your home with your own hands, you need to choose a place so that the future minibar fits perfectly and matches the interior of the entire room.

Selection of materials

The first step in any business is always planning. We must determine, firstly, what the future minibar will be made of and what size it will be, and, secondly, what we will store in it.

You can make a minibar with your own hands from wood, old chests of drawers or drawers, plastic or even more exotic materials: PVC pipes or cart wheels. Many people use metal canisters as material for their minibar. But this option is more suitable for men, since such bars are usually located in the garage - in their second home.

There are a lot of ideas for creating this interesting part of the interior. Therefore, you can borrow a few ideas by looking at photos of minibars for your home in the article, and bring them to life with your own hands.

The size of such a bar can also be varied. From small box holds up to ten bottles, up to a large rack. The main thing is not to overdo it and not make a stationary bar instead of a mobile one.

DIY minibar assembly

This is where our design flair comes in handy to choose what suits the interior, looks fresh and new. To make the assembly process more understandable, you need to consider it at specific example. You can assemble a minibar with your own hands from absolutely any material, but we will focus on a barrel. Yes, you can make a completely extraordinary mobile bar from an ordinary barrel.

We will need: bars, a handle and all the necessary tools.

The process of building your own DIY home minibar is simple. All you need is:

Place the barrel on its side.
Cut a hole in one of the walls for the door.
Using hinges, attach the cut piece of wood to the base to form a door.
Make shelves for bottles and glasses inside the barrel from wooden blocks.
Attach the handle to the door.
If desired, design the resulting product. You can use paints, decorative taps or stickers.
Build a counter on which the minibar will be located. It can be made from wooden or metal bars.

Anyone can make a minibar from a photo with their own hands, thereby decorating their garden and home.

What to fill the minibar with?

For some reason, many people are convinced that if they have a minibar with which they can mix cocktails, then they definitely need to fill it with a wide variety of different alcoholic drinks. This is, of course, wrong.

It will be enough to buy only some of the main and most popular and necessary options: classic vodka, cognac, brandy and liqueur. In addition, you should always store several liters of apple, citrus and grapefruit juice, Coca-Cola, strawberry syrup and cream. When you create cocktails, you will also need some professional tools:

shaker - a special glass for mixing;
strainer - a sieve for separating pulp and ice from the cocktail;
bar spoon - long spoon;
corkscrew.

There is no need to purchase many types of glasses; only three will be enough: rocks glass, highbull glass and shot glass.

Conclusion

Thus, we learned how to make a minibar with your own hands at home, arrange it for yourself and furnish it with the necessary things for your own convenience.

Of course, a minibar will always be inferior in practicality to the same static bar, but, in our opinion, it is impermissible to compare them. They serve different purposes, perform absolutely different functions, and even differ significantly in price.

A minibar is an interesting and practical thing that you can build with your own hands and thus introduce a new detail into the interior.

Buying a minibar in a furniture showroom or specialized shopping center is not a problem. Modern manufacturers offer a wide range of options for these interior items. But it’s quite possible to make them yourself from scrap materials, and then you’ll get a truly exclusive item that you can proudly show off to your relatives, friends, and acquaintances. Bookshelves, cabinets, tables, wine boxes and a host of other things that have fallen out of use for one reason or another are quite suitable as improvised materials for a fashionable piece of furniture.

At one time it was a pity to throw them away, and now they will serve the zealous owners.

For the convenience of storing various drinks, you can build a refrigerator into the bedside table.

In rural areas you can still find a cart wheel today. For most villagers it is of no value, but for a jack of all trades it is an exclusive find. Using a wheel is quite easy to create a rustic home minibar. This piece of furniture is made in two versions: from a whole wheel or its halves. To solve any type of bar you will need:
wheel or half of it;
boards or furniture board;
screws or self-tapping screws;
thick wire;
plugs or plugs for screws;
furniture varnish;
screwdriver;
saw or hacksaw;

medium-grain sandpaper. A very ordinary table of arbitrary dimensions is made from boards or furniture panels, a wheel is installed inside it - that’s all the basic operations for assembling a minibar. For fastening wooden elements

A mini bar made using a wheel can be made on one side and blank. Only then it is necessary to block one of its sides along the plane of the wheel with a furniture panel. In this case, craftsmen advise using two wheels located parallel to each other. If you do things this way, bottle holders may not be required. Two wheels located next to each other will fully cope with the role of holders. A home bar can be set up in a similar way using half a wheel. It will be smaller in size, but it can be installed on a bedside table, kitchen countertop or imitation fireplace - and a new stylish thing is ready. To emphasize the beautiful natural design of wooden products, they are opened with varnish, not forgetting to sand the sawn elements first. For finishing work They use stain and wood paint, the application of which becomes the finishing touch.

Return to contents

?
?
How to paste wallpaper?
A mini bar made of PVC pipes will fit very well into an interior in the style of hi-tech, loft, and minimalism.

What kind of products master craftsmen manage to make from PVC pipes! It’s easy to make a DIY bar from polymers. Such a thing is also good because it will fit into an interior in the style of hi-tech, loft, minimalism, and will come in handy exactly where classic wooden interior items begin to look like alien elements. A PVC mini bar can be made very quickly and does not require many tools. Its design usually does not include cup holders. And for the upcoming work you will need the following tools and materials:
hollow PVC pipes;

spray paint;

acetone;

universal spray primer;

self-adhesive double-sided tape;

hacksaw;

brush;

sandpaper of medium and fine grain.

If the minibar is made with wheels, then it can be moved anywhere if necessary.

First of all, you need to find a place where such an unusual bar will be installed. If there is an empty niche in your house or apartment, great! When there is no niche, an empty shelf or bedside table is used to make a mini bar.

The first measurement is the depth of the minibar. If the item is planned to be installed in a niche, we focus our calculations on it. Be sure to take into account the average height of the bottles that are supposed to be stored in it. Use a hacksaw to cut the pipes into the required lengths. But it’s easier to do it differently, more practically, saving your own time. When purchasing PVC pipes in shopping centers and stores, you can ask the seller to cut the pipes into equal lengths. This service is usually provided free of charge, just do not forget to first determine the total size of the pipes, the number and length of the sections. The edges of the pipes must be sanded with medium and fine grain sandpaper until they become smooth. If you neglect this operation, there is a high probability that the minibar will turn into a constant source of injury.

What is acetone used for? They use a brush to treat the surface of the pipes to remove oils from them, because they will prevent the paint from being applied evenly. One common mistake made by beginning craftsmen is to apply paint directly over PVC pipes. It is not right. Before painting, the pipes must be coated with a primer. Moreover, there are pipe options where layers of paint - primer - paint - primer are alternated. This option is the most optimal, because it creates a durable and aesthetic coating for PVC pipes. Once the paint and primer are dry, you can begin installing the pipes, which will require self-adhesive tape.

Return to contents

Bedside table mini bar

Making a wooden minibar bedside table will also not be difficult if you take it:

A mini bar made from a cart wheel is perfect for a rustic-style interior. It is made from a whole wheel and secured with a furniture board.

nightstand;

wooden planks:

paint;

tool for cutting planks;

ruler;

simple pencil.

The door by the bedside table does not have to be removed. If necessary, it is possible to decorate the inside of the minibar with a mirror after finishing making the shelves; it is glued using any glue suitable for wooden surfaces.

The algorithm of actions is as follows. First mark the boards. A cut is made in the middle and they are opened with paint, which must be secured with varnish. The planks are inserted into each other crosswise. If necessary, open the outer and inner parts of the bedside table with varnish.